Top-Rated Concrete Contractor Serving Cut and Shoot, TX | RV Pads, Shop Floors and Acreage Driveways in Cut and Shoot, TX

RV Pads and Covers From a Concrete Contractor in Cut and Shoot, TX

We pour RV pads thicker than a standard drive, with turned-down thickened edges, a rebar grid on chairs and a heavily compacted sub-base that won't rut when the ground is wet. An RV or travel trailer puts heavy weight on a few small points, and a thin slab cracks under the tires and jacks.

Our crews build metal and wood RV covers as part of the same job. We set footings or anchor points for the posts before the pour so the cover lines up with the slab. A cover with its slab usually takes us about a week from start to finish.

Areas We Serve Around Cut and Shoot, TX

Highway 105 East

Along Highway 105 East and the county roads off it, homes and shops sit well back from the road on large tracts. We pour the driveways that connect them, culvert approaches across the ditches, parking for work trucks and pads for businesses run from home.

Our office sorts out the paperwork at the entrance: a TxDOT permit where the drive comes directly off Highway 105, and the precinct's culvert process on county roads. We confirm which applies before we finalize the price, so the paperwork doesn't hold up your pour date.

Grangerland North Side

On the north side of Grangerland, between Cut and Shoot and Conroe, we pour gravel-to-concrete driveway conversions, carport and porch slabs, steps for manufactured homes, and shed pads. We size every slab to the load it will carry, so you're not paying for more concrete than the job needs. Our crew also routes the ready-mix truck to stay off septic fields and soft ground.

Shop Floors and Walkways to the Shop

Our shop floors are poured thick with steel throughout and thickened edges under the walls, because trucks, jacks, welders and dropped tools punish a thin slab. We coordinate the anchor bolt layout with your steel building supplier and leave sleeves for plumbing or electrical lines, which our licensed master plumbers and electricians can run.

We then connect the shop to the house with a concrete walkway, so you aren't crossing mud every time it rains. Our walks get a broom finish for traction, control joints at regular spacing, and a slight cross-slope so water runs off instead of sitting on the surface.

Matching Thickness to What Sits on the Slab

Every acreage slab we quote is sized to what goes on top, and the estimate explains why. You'll know exactly what you're paying for and where the thicker sections go before a single form is set.

All of it is 3,000-plus PSI concrete from local ready-mix plants, with fiber mesh to reduce shrinkage cracks. Where the ground is soft or the clay is especially active, our crew over-excavates and replaces it with select fill before building the base.

Long Driveways With No HOA

We design HOA-free drives around how you actually use the property. That might be a ribbon drive for a long run to the back of the land, a full-width drive near the house, a trailer turnaround or a pull-off for deliveries. We also phase long drives, pouring the section by the house now and leaving steel dowels at the end so the next stretch ties in later.

Our grade sheds water to both sides, and on drives that cross low ground, we add culverts or a crowned section so the concrete isn't sitting in water after every storm. We can also add a gravel shoulder along long drives where mowers and trucks tend to drift off the edge.

Generator, Equipment and Tank Pads

We pour standby-generator pads for Cut and Shoot owners who are tired of long outages: level, reinforced and sized to the unit's footprint with clearance around it. Our licensed electricians and plumbers can handle the transfer switch wiring and gas line as part of the same job.

Our crews pour the same kind of pads for AC condensers, water tanks, well equipment, feeders and tractors. Each one gets a compacted base, steel and a slight slope to shed water, so the equipment sits level and stays out of the mud.

Porches, Patios and Fire Pit Areas

We pour full-length back porch slabs, patios with fire-pit areas and covered outdoor kitchens that look out over the land. Each one gets a slight fall away from the house, with an optional stamped or textured surface. Because we build covers, kitchens and fences ourselves, one crew handles the whole project, and a full outdoor bundle usually takes us about two weeks.

How We Handle an Acreage Pour

1. Walk the land

   Our owner meets you on the property, looks at access, slope, trees, septic and the road entrance, and listens to what you need.

2. Written price and permits

   We send a written estimate with thicknesses, steel, finish and every line item, good for three months. Our office calls 811 and lines up the culvert inspection or state highway permit.

3. Prep and steel

   Our crew clears, grades, compacts the base, sets forms and ties the rebar grid on chairs.

4. Pour and walkthrough

   We pour and finish, usually in one to two days, and our owner walks the work with you once it's cured.

Grouping Several Pours Into One Trip

We often pour a shop floor, a generator pad and a walkway in the same mobilization, which saves on setup and keeps your property torn up for fewer days. Tell us everything on your list at the site visit, and we'll price it together and separately so you can decide what to build now and what to save for later.

Our Most Requested Concrete Services in Cut and Shoot, TX

Concrete Problems We Fix Most in Cut and Shoot

Out on acreage, most of the repair calls we get come from slabs built too thin for the weight they carry:

• RV pads cracked under the tires and leveling jacks
• Shop floors broken at the overhead door
• Approaches crumbling where trucks turn in off the road
• Gravel drives that wash out and rut every wet season
• Carport slabs settling under the posts

We rebuild them with the right thickness for the load, a heavily compacted base, select fill where the clay is especially active, and steel throughout. Our owner marks the thicker sections on your estimate so you can see exactly where the extra concrete goes.

Add-Ons Cut and Shoot Owners Choose

Since we're already on site with forms and steel, many of our customers add one of these to the same mobilization:

• A metal or wood RV cover or carport built over the new slab
• Sleeves for water and power to the shop, run by our licensed master plumbers and electricians
• A turnaround pad for trailers at the end of the drive
• A thickened apron at the shop's overhead door
• A back porch slab or fire-pit patio facing the land
• A gravel shoulder along a long drive where mowers drift off the edge

Each add-on is priced on its own line, our written quote holds for three months, and every pour carries our one-year workmanship warranty and 100% satisfaction guarantee.

How Long Cut and Shoot Projects Take Us

These are the ranges we write into most Cut and Shoot estimates. Weather and permits can move them, and we tell you up front when they will:

Pricing and Scheduling Acreage Work

Our acreage pricing comes from square footage, thickness, site prep, truck access and any approach or culvert. We list each in writing with no hidden fees, and any change is written up and approved before we do it. For bigger projects like a shop floor plus a drive, we take a deposit and progress draws instead of the full amount up front.

We finish most driveways in two to three days, and most pours take one to two. Our discounts for active-duty military, veterans, seniors, first responders, teachers and school staff apply in Cut and Shoot, and our workmanship is backed by a one-year warranty. You can walk on new concrete after about a day.

Cut and Shoot Concrete FAQs